1 of 6 1.0 features supports qualcomm ? quick charge tm 2.0 (qc2.0) technology high voltage dedicated charging port (hvdcp) double-layer cable protection: x secondary side (iw629): proprietary d+/d- over- voltage protection (ovp) addresses v bus d+/d- soft shorts x primary side (iw1780): smartdefender? smart hiccup technology reduces average output power at fault conditions without latch proprietary secondary-to-primary digital communication eliminates discrete decoders in the primary side and simplifes system designs single opto-coupler transmits all information for rapid charge: output voltage requests, output current limits, output voltage undershoot, over-voltage protection, and fault and reset signals backward compatible with usb battery charging specifcation revision 1.2 (usb bc1.2) dedicated charging port (dcp) pin-to-pin compatible with iw626 programmable active fast discharge from 9v to 5v at mobile device (md) unplug or upon request with built-in switch or external switch normally off state with <120 m a cut-off current during 5v steady-state operation to achieve <10mw power consumption at no load wide operating voltage range from 3v to 25v built-in opto-coupler led driver with minimum driving current of 2ma 6-lead sot-23 package 2.0 description the iw629 is an ac/dc secondary-side controller compatible with the qualcomm quick charge 2.0 usb interface and secondary-to-primary communication protocol, allowing rapid charging of qc2.0-enabled mobile devices. the iw629 resides on the secondary side of an ac/dc power supply and allows the adapter to be confgured for multi-level output such as 5v and 9v, depending on the voltage requested by the mobile device. it can be used in dialogs primary-side controlled ac/ dc systems to achieve fast voltage transition, low no-load power consumption, and fast dynamic load response. the iw629 implements dialogs proprietary secondary-to- primary digital communication technique. when paired with dialogs primary-side iw1780 controller, the iw629 eliminates the discrete decoders in the primary side, simplifying system designs. it uses one opto-coupler to transmit all necessary information for rapid charging, including output voltage requests, output current limits, output voltage undershoot, output over-voltage, and fault and reset signals. it also has a built-in opto-coupler led driver to minimize the bill of material cost. the iw629 and iw1780 provide double-layer cable protection. on the secondary side, the iw629 incorporates dialogs proprietary d+/d- over-voltage protection to address v bus d+/ d- soft shorts. on the primary side, the iw1780 uses dialogs smartdefender advanced hiccup technology to reduce the average output power during soft shorts without latch. dialogs innovative, proprietary technology ensures that power supplies designed with the iw629 and iw1780 can provide multi-level output voltage confguration, with user-selected various output current limit combinations. furthermore, the chipset can achieve <10mw no-load power consumption at 5v, 2a output setting and fast dynamic load response in typical ac/dc rapid charge adapter designs. qualcomm ? quick charge tm 2.0 is a product of qualcomm technologies, inc. 3.0 applications rapid-charging ac/dc adapters for smart phones, tablets, and other portable devices iw629 product summary ac/dc secondary-side controller for qualcomm ? quick charge tm 2.0 usb interface with soft-short protection rev. 0.5 preliminary iw629 ? 2015 dialog semiconductor (uk) ltd. product summary
2 of 6 u2 iw629 v out rtn + + + u1 iw1780 v sense sd v cc gnd 1 2 3 8 7 6 4 5 ntc l n output cs/cdc dlnk asu r cdc 3 1 drv gnd 2 4 6 5 dis v cc d- d+ d+ d- figure 3.1: iw629 typical application circuit for multi-level output voltage and current (using iw1780 as primary-side controller. achieving <10mw no-load power consumption) figure 3.2: iw629 typical application circuit for multi-level output voltage and current (using iw1780 as primary-side controller and iw671 as synchronous rectifer controller . achieving < 20mw no-load power consumption) + + u1 iw1780 v sense sd v cc gnd 1 2 3 8 7 6 4 5 ntc l n output cs/cdc dlnk asu r cdc v out rtn vps drv v in v cc 1 2 3 8 7 6 4 5 plrin drain + + gnd out u3 iw671 u2 iw629 3 1 drv gnd 2 4 6 5 dis v cc d- d+ d+ d- iw629 product summary ac/dc secondary-side controller for qualcomm ? quick charge tm 2.0 usb interface with soft-short protection rev. 0.5 preliminary iw629 ? 2015 dialog semiconductor (uk) ltd. product summary
3 of 6 4.0 pinout description pin # name type pin description 1 dis analog output discharging circuit and external fet drive. used for fast discharging of output capacitor. also can be used for driving external fet. 2 drv analog output external circuit drive. can be used for opto-coupler led drive with automatic current limiting for transmitting signals to primary side. 3 v cc power supply ic power supply. 4 d- analog input/ output usb d- signal. 5 gnd ground ground. 6 d+ analog input usb d+ signal. iw629 dis drv v cc d+ gnd d- 1 2 3 6 4 5 figure 4.1: 6 lead sot-23 package iw629 product summary ac/dc secondary-side controller for qualcomm ? quick charge tm 2.0 usb interface with soft-short protection rev. 0.5 preliminary iw629 ? 2015 dialog semiconductor (uk) ltd. product summary
4 of 6 absolute maximum ratings are the parameter values or ranges which can cause permanent damage if exceeded. 5.0 absolute maximum ratings parameter symbol value units dis (pin 1) voltage v dis 30 v drv (pin 2) voltage v drv 30 v v cc (pin 3) voltage v cc 30 v d- (pin 4) voltage v d- -0.3 to 7 v d+ (pin 6) voltage v d+ -0.3 to 7 v continuous dc current at drv pin (v drv = 11v) i drv 25 ma continuous dc supply current at v cc pin (v cc = 12v) i vcc 25 ma peak current at dis pin (v dis = 12v) i dis 600 ma maximum junction temperature t jmax 150 c operating junction temperature t jopt -40 to 150 c storage temperature t stg -65 to 150 c esd rating per jedec jesd22-a114 (d+ and d- pins) 4,000 v esd rating per jedec jesd22-a114 (all other pins) 2,000 v iw629 product summary ac/dc secondary-side controller for qualcomm ? quick charge tm 2.0 usb interface with soft-short protection rev. 0.5 preliminary iw629 ? 2015 dialog semiconductor (uk) ltd. product summary
5 of 6 6.0 physical dimensions 1 3 4 6 5 2 6-lead sot package d compliant to jedec standard mo-178ab controlling dimensions are in millimeters this package is rohs compliant and halide free. soldering temperature resistance: [a] package is ipc/jedec std 020d moisture sensitivity level 1 [b] package exceeds jedec std no. 22-a111 for solder immersion resistance; packages can withstand 10 s immersion < 260oc dimension d does not include mold flash, protrusions or gate burrs. mold flash, protrusions or gate burrs shall not exceed 0.25 mm per side. the package top may be smaller than the package bottom. dimensions d and e1 are are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs and interlead flash, but including any mismatch between top and bottom of the plastic body. seating plane a1 coplanarity 0.10 e1 b e e1 a a2 c l symbol millimeters a1 min max 0.00 0.15 a - 1.45 b 0.30 0.50 c 0.08 0.22 d 2.80 3.00 e e1 e 0.95 bsc e1 1.90 bsc 2.80 bsc 1.60 bsc l 0.30 0.60 0 8 a2 0.90 1.30 e 2.90 bsc part number options package description IW629-20 1 supports qc2.0 5v/9v, k = 0.411 for 5v/9v cc limits, 4.75v undershoot threshold for 5v, 11k dynamic preload at 5v sot-23 tape & reel 2 note 1: the IW629-20 is a customized product option with 12v disabled. adapters designed with this product option may not pass qc2.0 hvdcp compliancy test. note 2: tape & reel packing quantity is 3,000/reel. minimum ordering quantity is 3,000. iw629 product summary ac/dc secondary-side controller for qualcomm ? quick charge tm 2.0 usb interface with soft-short protection rev. 0.5 preliminary iw629 ? 2015 dialog semiconductor (uk) ltd. product summary
disclaimer information in this document is believed to be accurate and reliable. however, dialog semiconductor does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information. dialog semiconductor furthermore takes no responsibility whatsoever for the content in this document if provided by any information source outside of dialog semiconductor. dialog semiconductor reserves the right to change without notice the information published in this document, including without limitation the specifcation and the design of the related semiconductor products, software and applications. applications, software, and semiconductor products described in this document are for illustrative purposes only. dialog semiconductor makes no representation or warranty that such applications, software and semiconductor products will be suitable for the specifed use without further testing or modifcation. unless otherwise agreed in writing, such testing or modifcation is the sole responsibility of the customer and dialog semiconductor excludes all liability in this respect. customer notes that nothing in this document may be construed as a license for customer to use the dialog semiconductor products, software and applications referred to in this document. such license must be separately sought by customer with dialog semiconductor. all use of dialog semiconductor products, software and applications referred to in this document are subject to dialog semiconductors standard terms and conditions of sale , unless otherwise stated. ? dialog semiconductor (uk) ltd. all rights reserved. rohs compliance dialog semiconductor complies to european directive 2001/95/ec and from 2 january 2013 onwards to european directive 2011/65/eu concerning restriction of hazardous substances (rohs/rohs2). dialog semiconductors statement on rohs can be found on the customer portal https://support.diasemi.com/ . rohs certifcates from our suppliers are available on request. 6 of 6 contacting dialog semiconductor united kingdom dialog semiconductor (uk) ltd phone: +44 1793 757700 germany dialog semiconductor gmbh phone: +49 7021 805-0 the netherlands dialog semiconductor b.v. phone: +31 73 640 88 22 email info_pcbg@diasemi.com north america dialog semiconductor inc. phone: +1 408 845 8500 japan dialog semiconductor k. k. phone: +81 3 5425 4567 taiwan dialog semiconductor taiwan phone: +886 281 786 222 web site: www.dialog-semiconductor.com singapore dialog semiconductor singapore phone: +65 648 499 29 hong kong dialog semiconductor hong kong phone: +852 2607 4271 korea dialog semiconductor korea phone: +82 2 3469 8200 china dialog semiconductor (shenzhen) phone: +86 755 2981 3669 dialog semiconductor (shanghai) phone: +86 21 5424 9058 iw629 product summary ac/dc secondary-side controller for qualcomm ? quick charge tm 2.0 usb interface with soft-short protection rev. 0.5 preliminary iw629 ? 2015 dialog semiconductor (uk) ltd. product summary
|
